Phone.: (03) 9311 7822 | sales@liquipvictoria.com.au

Categories

CIF Series Crushable Incinerable Cartridges

The Facet CIF Series high efficiency pleated paper filter cartridges are designed to effectively remove solid contaminants from fuels.

Media with high efficiency throughout the life of the cartridge is available in ratings from .5 to 5 microns. We recommend replacing cartridges when the differential pressure reaches 15 psi (1.03 bar). Effective life above 15 psi (1.03 bar) is minimal.

All cartridges are 6" (152 mm) outside diameter. To simplify maintenance, we offer one piece cartridges in three lengths:

  • single-length of 14½" (370 mm)
  • double-length of 28¾" (730 mm)
  • triple-length of 43¼" (1090 mm).

One triple-length cartridge replaces three single-length.

To use the CIF Series cartridge requires the one time installation of either a single, double or triple length centre tube kit. Each kit contains all necessary hardware and components required to convert any housing fitted for 6" (152 mm) OD x 3½" (89 mm) ID diameter cartridges.

These high efficiency pleated paper filter cartridges designed to effectively remove solid contaminants in applications such as:

  • Gasoline
  • Coolants
  • Kerosene
  • Rolling Oils
  • Diesel
  • Jet Fuel
  •  AV-Gas
  • Industrial Water
  •  Solvents (Stoddard and Ketone Based)

The filtration of potable liquids is not recommended with this series of filter cartridges.

We recommend replacing cartridges when the differential pressure reaches 15 psi. Effective life above 15 psi is minimal.

  • Crushable - can reduce your disposal volume approx. 80%
  • No metal components
  • Incinerable
  • Cartridges alignment is executed at top of centre tube
  • Lightweight - contributes to reducing change out time
  • Same performance and efficiency as M Series high efficiency pleated paper filter cartridges

Flow direction
Outside to in

pH Range
From 5 To 9

Max. recommended operating temperature
240°F (115°C)

Initial differential pressure
2 psi (.14 kg/cm²) or less

Design collapse pressure
75 psi (5.25 kg/cm²)

Materials
Constructed with high efficiency pleated paper.
No metal components—end caps and centre tubes are engineered plastics.
Gaskets are Buna-N—other materials available by request

Installation Instructions:

To Install The CIF Series Centre Tube

  1. Remove existing filter cartridge. NOTE: Leave centre rod in position.
  2. Identify bottom of centre tube. Only the top of center tube will accept top adaptor
  3. Place centre tube assembly with the bottom guide down making sure it is properly aligned on the existing cartridge adaptor.
  4. For kit numbers CIF2 and CIF3, be sure to properly align centring guide over centre rod.
  5. Slide top adaptor over centre rod and secure in centre tube using jam nut (thinner of two nuts). Tighten to 5 foot pounds (6.78 Nm).
    At this point you have successfully installed your permanent centre tube.

To Install the CIF Series Cartridge

  1. Slide cartridge over centre tube. Install NEW black yoke domed head up. 
  2. Place rubber gasket washer (9) (supplied with filter cartridge) over centre rod.
  3. Place flat steel washer (10) over rubber gasket washer.
  4. Place steel lock washer over flat steel washer and secure 5 foot pounds (6.78 Nm) with hex nut
Item Micron Rating Nominal Length
in mm
CIF0.5LX3 0.5 44 5/8 1133
CIF1 1 14½ 370
CIF1X2 1 28¾ 730
CIFLX3 1 44 5/8 1133
CIF2 2

14½

370
CIF2X2 2 28¾ 730
CIF2LX3 2 44 5/8 1133
CIF5 5

14½

370
CIF5X2 5 28¾ 730
CIFLX3 5 44 5/8 1133

 

 

Related Products